User Tools

Site Tools


kit:crowbox2_v20_bom

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
kit:crowbox2_v20_bom [2018/08/01 11:32] – [Styrene Housing Parts] - Final styrene parts stevekit:crowbox2_v20_bom [2023/02/06 02:24] (current) admin
Line 1: Line 1:
-====== Introduction ====== +====== Bill of Materials (BOM) ====== 
-This bill of materials (BOMis divided into three sections: + 
-  - **Housing Parts** - The laser-cut acrylic and styrene parts from which the Crowbox housing is built. +This BOM is divided into three sections: 
-  - **Electronics Parts** - The parts required to construct the electronic 'guts' of the Crowbox.+  - **Housing Parts** - The laser-cut acrylic and styrene parts from which the CrowBox housing is built. 
 +  - **Electronics Parts** - The parts required to construct the electronic 'guts' of the CrowBox.
   - **Tools & Supplies** - Tools and shop/household supplies needed to complete the build.   - **Tools & Supplies** - Tools and shop/household supplies needed to complete the build.
  
-Total cost will depend on where you buy your parts plus shipping, but we worked hard to keep it below USD $100.+Total cost will depend on where you buy your parts plus shipping, but we worked hard to keep it as low as possible - likely between $200-300 USD.
  
 ====== Housing Parts ====== ====== Housing Parts ======
 ===== Acrylic Housing Parts ===== ===== Acrylic Housing Parts =====
-Parts laser cut from acrylic sheets which are 1/8 inch (or 3mm, depending on the provider) thick. You may download the ready-to-cut geometry files for the Crowbox housing parts for free, [[kit:geometry_files|right here]]. If you have access to a laser cutter, you may cut these yourselves. Otherwise, you may be able to have the parts cut at a local MakerSpace. You can also buy fabricated Crowbox parts online, directly from a provider like [[http://thecrowbox.com/wiki/doku.php?id=kit:ponoko_guide|Ponoko]].+Parts laser cut from acrylic sheets which are 1/8 inch (or 3mm, depending on the provider) thick. You may download the ready-to-cut geometry files for the CrowBox housing parts for free, [[kit:geometry_files|right here]]. If you have access to a laser cutter, you may cut these yourselves. Otherwise, you may be able to have the parts cut at a local MakerSpace. You can also buy fabricated CrowBox parts online, directly from a provider like [[http://theCrowBox.com/wiki/doku.php?id=kit:ponoko_guide|Ponoko]].
  
-The Crowbox is built using three different colors of acrylic: A light color, a dark color, and transparent. The transparent parts must be transparent so that birds can see the rewards that are on offer. You may choose whichever light and dark colors please you, but you should make sure to pick colors which result in a neutral, natural color scheme in your intended environment.+The CrowBox is built using three different colors of acrylic: A light color, a dark color, and transparent. The transparent parts must be transparent so that birds can see the rewards that are on offer. You may choose whichever light and dark colors please you, but you should make sure to pick colors which result in a neutral, natural color scheme in your intended environment.
  
 Click on any image in this section to view a larger version. Click on any image in this section to view a larger version.
Line 23: Line 24:
 |1| Sled | {{:kit:housing:housing_sled.jpg?direct&256|}} | | |1| Sled | {{:kit:housing:housing_sled.jpg?direct&256|}} | |
 |2| Sled Shelves | {{:kit:housing:housing_sled_shelves.jpg?direct&256|}} | | |2| Sled Shelves | {{:kit:housing:housing_sled_shelves.jpg?direct&256|}} | |
 +|2| Sled Shelf Supports | {{:kit:housing:housing_sled_shelf_supports.png?direct&256|}} | |
 |1| Servo Spine | {{:kit:housing:housing_servo_spine.jpg?direct&256|}} | | |1| Servo Spine | {{:kit:housing:housing_servo_spine.jpg?direct&256|}} | |
 |1| Sliding Lid | {{:kit:housing:housing_sliding_lid.png?direct&256|}} | | |1| Sliding Lid | {{:kit:housing:housing_sliding_lid.png?direct&256|}} | |
Line 51: Line 53:
 |4| Ramp Support Stringers | {{:kit:housing:housing_ramp_support_stringers.png?direct&256|}} | | |4| Ramp Support Stringers | {{:kit:housing:housing_ramp_support_stringers.png?direct&256|}} | |
 |2| Basket Perches | {{:kit:housing:housing_basket_perches.png?direct&256|}} | | |2| Basket Perches | {{:kit:housing:housing_basket_perches.png?direct&256|}} | |
-|2| Sled Shelf Supports | FIXME | | 
 |1| Perch Hook | {{:kit:housing:housing_perch_hook.png?direct&256|}} | | |1| Perch Hook | {{:kit:housing:housing_perch_hook.png?direct&256|}} | |
 |1| Basket Spine | {{:kit:housing:housing_basket_spine.png?direct&256|}} | | |1| Basket Spine | {{:kit:housing:housing_basket_spine.png?direct&256|}} | |
 |1| Base Reinforcing Ring | {{:kit:housing:housing_base_reinforcing_ring.jpg?direct&256|}} | | |1| Base Reinforcing Ring | {{:kit:housing:housing_base_reinforcing_ring.jpg?direct&256|}} | |
-|1| Coin Magazine Front Panel | {{:kit:housing:housing_coin_magazine_front_panel.png?direct&256|}} | |+|1| Coin Magazine Front Panel | {{:kit:housing:housing_coin_magazine_front_panel.png?direct&256|}} | Note the Coin Magazine parts are designed for \\ U.S. Quarters and may need to be \\ adjusted for coins of different sizes / thicknesses |
 |1| Coin Magazine Rear Panel | {{:kit:housing:housing_coin_magazine_rear_panel.png?direct&256|}} | | |1| Coin Magazine Rear Panel | {{:kit:housing:housing_coin_magazine_rear_panel.png?direct&256|}} | |
 |1| Coin Magazine Cap | {{:kit:housing:housing_coin_magazine_cap.png?direct&256|}} | | |1| Coin Magazine Cap | {{:kit:housing:housing_coin_magazine_cap.png?direct&256|}} | |
Line 63: Line 64:
 |1| Perch Fulcrum | {{:kit:housing:housing_perch_fulcrum.png?direct&256|}} | | |1| Perch Fulcrum | {{:kit:housing:housing_perch_fulcrum.png?direct&256|}} | |
 |1| Coin Intake Ramp | {{:kit:housing:housing_coin_intake_ramp.png?direct&256|}} | | |1| Coin Intake Ramp | {{:kit:housing:housing_coin_intake_ramp.png?direct&256|}} | |
-|1| Crowbox Box-End Wrench | FIXME | | 
-|1| Crowbox Open-End Wrench | FIXME | | 
  
 ===== Styrene Housing Parts ===== ===== Styrene Housing Parts =====
Line 73: Line 72:
 |2| Lower Ramp Panels | {{:kit:housing:housing_ramp_lower_panel.jpg?direct&256|}} | | |2| Lower Ramp Panels | {{:kit:housing:housing_ramp_lower_panel.jpg?direct&256|}} | |
 |1| Basket Food Liner | {{:kit:housing:housing_basket_food_liner.png?direct&256|}} | | |1| Basket Food Liner | {{:kit:housing:housing_basket_food_liner.png?direct&256|}} | |
-|1| Rotor Pin Wrap | {{:kit:housing:housing_rotor_pin_wrap.png?direct&256|}} | |+|1| Rotor Pin Wrap | {{:kit:housing:housing_rotor_pin_wrap.png?direct&256|}} | This part is no longer used but still appears\\ on the sheet of styrene parts |
  
  
Line 83: Line 82:
 | 9 sq. in. | Conductive Copper Tape | {{:kit:bom:bom_copper_tape_256.jpg?nolink|}} | Used in building the coin sensor. Sometimes called "copper shielding tape" or "emi shielding tape". A 1 inch wide roll is recommended. \\ \\ **NOTE:** A suitable item can be found at home and hardware stores, often labeled as 'slug and snail barrier tape', if electrical shielding tape is difficult to find. | | 9 sq. in. | Conductive Copper Tape | {{:kit:bom:bom_copper_tape_256.jpg?nolink|}} | Used in building the coin sensor. Sometimes called "copper shielding tape" or "emi shielding tape". A 1 inch wide roll is recommended. \\ \\ **NOTE:** A suitable item can be found at home and hardware stores, often labeled as 'slug and snail barrier tape', if electrical shielding tape is difficult to find. |
 | 24 sq.in. | Grip/Traction Tape | {{:kit:bom_traction_tape_256.jpg?nolink|}} | Used to provide non-skid surfaces for birds to stand. \\ \\ **NOTE:** Duct tape may be used in a pinch if you are unable to source traction tape. | | 24 sq.in. | Grip/Traction Tape | {{:kit:bom_traction_tape_256.jpg?nolink|}} | Used to provide non-skid surfaces for birds to stand. \\ \\ **NOTE:** Duct tape may be used in a pinch if you are unable to source traction tape. |
 +|asstd.| M2 and M3 machine screws with nuts | {{ :kit:bom:bom_machine_screws_256.jpg?nolink |}} | 2mm and 3mm machine screws. 3mm screws in 8mm and 10mm lengths, 2mm screws in 12mm length. Pan head or socket cap recommended. \\ \\ **NOTE:** Avoid 'countersink' style heads \\ **NOTE:** It's easiest to buy a machine screw assortment that contains assorted 3mm and 2mm screws, but these can also be bought individually and in small packets at Home Depot or other home building supply stores. Unless you're supplying a home shop for multiple projects this is probably a better solution than buying a large quantity online. |
 |2| 1/8" Hitch pins | {{:kit:bom:bom_hitch_pin_256.jpg?nolink|}} | Used to secure the perch platform while allowing for easy removal. \\ \\ **NOTE:** These are optional- You can use small plastic cable ties instead, as the perch platform rarely needs to be removed.  | |2| 1/8" Hitch pins | {{:kit:bom:bom_hitch_pin_256.jpg?nolink|}} | Used to secure the perch platform while allowing for easy removal. \\ \\ **NOTE:** These are optional- You can use small plastic cable ties instead, as the perch platform rarely needs to be removed.  |
  
  
 ====== Electronics Parts ====== ====== Electronics Parts ======
-The Crowbox requires a few common electronic components, listed here. We are not affiliated with any online vendors, but we do provide some recommendations for where you can find the required items:+The CrowBox requires a few common electronic components, listed here. We are not affiliated with any online vendors, but we do provide some recommendations for where you can find the required items:
  
 **eBay**\\ **eBay**\\
-Probably the least expensive way to get everything you need. The parts needed for a Crowbox are very common and there are usually multiple sellers offering each part, many offering free shipping. +Probably the least expensive way to get everything you need. The parts needed for a CrowBox are very common and there are usually multiple sellers offering each part, many offering free shipping. 
  
 **amazon.com** (prime)\\ **amazon.com** (prime)\\
Line 103: Line 103:
 |2| Micro limit switch w/roller | {{:kit:bom:bom_micro_limit_sw_256.jpg?nolink|}} | \\ Be sure to buy the black-and-white switch pictured here. \\ \\ **Online shopping search term:** ultra mini micro limit switch roller  | |2| Micro limit switch w/roller | {{:kit:bom:bom_micro_limit_sw_256.jpg?nolink|}} | \\ Be sure to buy the black-and-white switch pictured here. \\ \\ **Online shopping search term:** ultra mini micro limit switch roller  |
 |1| PCB mount pushbutton | {{:kit:bom:bom_pcb_button_256.jpg?nolink|}} | \\ 6x6mm size recommended \\ \\ **Online shopping search term:** pcb mount dip tactile switch 6mm | |1| PCB mount pushbutton | {{:kit:bom:bom_pcb_button_256.jpg?nolink|}} | \\ 6x6mm size recommended \\ \\ **Online shopping search term:** pcb mount dip tactile switch 6mm |
-|1| MG995 Servo | {{:kit:bom:bom_mg995_servo_256.jpg?nolink|}} | \\ **Online shopping search term:** MG995 servo | +|1| MG995, Futaba 3003 or 3004 180 degree Servo | {{:kit:bom:bom_mg995_servo_256.jpg?nolink|}} | **NOTE:** These servos are manufactured by several different companies and are sometimes sold with different assortments of accessories. Ensure that the servo you buy is a 180 degree servo and that it comes with a **six star horn** accessory, shown here: {{ :kit:bom:bom_six_star_horn_256.jpg?nolink&200 |}} \\ **Online shopping search term:** "MG995 servo", "Futaba 3003 servo", or "Futaba 3004 servo" 
-|asstd| Dupont jumper wires | {{:kit:bom:bom_dupont_ribbon_gen_256.jpg?nolink|}} | FIXME |+|asstd| Dupont jumper wires | {{:kit:bom:bom_dupont_ribbon_gen_256.jpg?nolink|}} | Select 10cm length, one set of male-to-male and one set of male-to-female. \\ \\ **Online shopping search term:** 10cm dupont m-m f-m | 
 +|1 set| Dupont male with alligator clip | {{ :kit:bom:bom_dupont_gators.jpg?nolink |}} | Dupont male on one end, alligator clip on the other. \\ \\ **NOTE:** only two alligator clip wires are required. You can make your own by soldering alligator clips to ordinary dupont wires, if you already have the gator clips.\\ \\ **Online shopping search term:** dupont alligator clip |
 |1| 5mm terminal block | {{:kit:bom:bom_5mm_terminal.jpg?nolink|}} | \\ Color may be green or blue- it does not matter which you buy, just be sure to get 5mm pitch. \\ \\ **Online shopping search term:** 5mm terminal block 2p | |1| 5mm terminal block | {{:kit:bom:bom_5mm_terminal.jpg?nolink|}} | \\ Color may be green or blue- it does not matter which you buy, just be sure to get 5mm pitch. \\ \\ **Online shopping search term:** 5mm terminal block 2p |
 +|asstd.| 3mm standoffs | {{ :kit:bom:bom_3mm_standoffs.jpg?nolink |}} | Nylon is recommended but brass is fine. Only three standoffs are required, recommended height is 8mm. \\ \\ **NOTE:** It's possible to cobble together standoffs using M3 screws and multiple nuts. \\ \\ **Online shopping search term:** 3mm standoff kit |
 |1| 2.1 x 5.5mm female DC power pigtail | {{:kit:bom:bom_power_pigtail_256.jpg?nolink|}} | Only one is required but almost always sold in lots of 10 or more. Be sure to get the **FEMALE** type \\ \\ **Online shopping search term:** 2.1 x 5.5mm female power pigtail | |1| 2.1 x 5.5mm female DC power pigtail | {{:kit:bom:bom_power_pigtail_256.jpg?nolink|}} | Only one is required but almost always sold in lots of 10 or more. Be sure to get the **FEMALE** type \\ \\ **Online shopping search term:** 2.1 x 5.5mm female power pigtail |
 |1| 5 volt 2 amp (5V2A) power supply | {{:kit:bom:bom_5v2a_adapter_256.jpg?nolink|}} | These are inexpensive and widely-available. The appearance of the wall socket plug may vary from what you see here. \\ \\ **NOTE:** Be sure that you buy an adapter with 5.5mm plug! \\ **NOTE:** Be sure to buy a 2 amp adapter! \\ \\ **Online shopping search term:** 5v2a 5.5x2.1mm DC power supply | |1| 5 volt 2 amp (5V2A) power supply | {{:kit:bom:bom_5v2a_adapter_256.jpg?nolink|}} | These are inexpensive and widely-available. The appearance of the wall socket plug may vary from what you see here. \\ \\ **NOTE:** Be sure that you buy an adapter with 5.5mm plug! \\ **NOTE:** Be sure to buy a 2 amp adapter! \\ \\ **Online shopping search term:** 5v2a 5.5x2.1mm DC power supply |
 +
 +
 ====== Tools & Supplies ====== ====== Tools & Supplies ======
 Many of these things are probably already lying around a typical home. Many of these things are probably already lying around a typical home.
Line 114: Line 118:
 |1| Small screwdriver set | {{:kit:bom:bom_screwdriver_set_256.jpg?nolink&512|}} | Select a small tool set that includes drivers of the type required for your M2 and M3 machine screws. Also make sure there's a small phillips driver for adjusting the screws on the 5mm terminals. |  |1| Small screwdriver set | {{:kit:bom:bom_screwdriver_set_256.jpg?nolink&512|}} | Select a small tool set that includes drivers of the type required for your M2 and M3 machine screws. Also make sure there's a small phillips driver for adjusting the screws on the 5mm terminals. | 
 |1| Wire Strippers | {{:kit:bom:bom_wire_strippers_256.jpg?nolink|}} | Any type will do. If you strip wire with your teeth, don't tell your dentist! |  |1| Wire Strippers | {{:kit:bom:bom_wire_strippers_256.jpg?nolink|}} | Any type will do. If you strip wire with your teeth, don't tell your dentist! | 
-|5oz| SciGrip/Weld-On #16 acrylic cement | {{ :kit:bom:bom_scigrip16_5oz_256.jpg?nolink |}} | This is the primary adhesive for the acrylic parts of the Crowbox. This product is sold in multiple sizes. The small size (5 oz) is plenty of cement to build a single Crowbox. \\ \\ **NOTE:** Be sure to get the **#16** formulation. May also be called 'syrup' or labelled 'syrupy consistency'+|5oz| SciGrip/Weld-On #16 acrylic cement | {{ :kit:bom:bom_scigrip16_5oz_256.jpg?nolink |}} | This is the primary adhesive for the acrylic parts of the CrowBox. This product is sold in multiple sizes. The small size (5 oz) is plenty of cement to build a single CrowBox. \\ \\ **NOTE:** Be sure to get the **#16** formulation. May also be called 'syrup' or labelled 'syrupy consistency'  \\ \\ **NOTE:** An applicator tip is essential for proper, precise application of the cement. If your cement doesn't come with one (most don't) you'll need to buy it separately or you're going to be cursing and screaming when you go to build.  
 |1| Hot glue gun | {{:kit:bom:bom_glue_gun_256.jpg?nolink|}} | Used mainly for creating weathertight seals at critical joints. A high-temperature model is best, but any hot melt glue gun will do. | |1| Hot glue gun | {{:kit:bom:bom_glue_gun_256.jpg?nolink|}} | Used mainly for creating weathertight seals at critical joints. A high-temperature model is best, but any hot melt glue gun will do. |
 |1| Hot Glue Sticks | {{:kit:bom:bom_glue_sticks_256.jpg?nolink|}} | The right size and spec for your hot glue gun. Use the type labeled "acrylic" if you can find them. |  |1| Hot Glue Sticks | {{:kit:bom:bom_glue_sticks_256.jpg?nolink|}} | The right size and spec for your hot glue gun. Use the type labeled "acrylic" if you can find them. | 
kit/crowbox2_v20_bom.1533148346.txt.gz · Last modified: 2018/08/01 11:32 by steve