User Tools

Site Tools


kit:crowbox2_v20_bom

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
kit:crowbox2_v20_bom [2018/09/11 16:22]
steve [Electronics Parts] - added standoffs
kit:crowbox2_v20_bom [2019/01/05 15:08] (current)
steve [Electronics Parts] - Added note for six star horn
Line 72: Line 72:
 |2| Lower Ramp Panels | {{:​kit:​housing:​housing_ramp_lower_panel.jpg?​direct&​256|}} | | |2| Lower Ramp Panels | {{:​kit:​housing:​housing_ramp_lower_panel.jpg?​direct&​256|}} | |
 |1| Basket Food Liner | {{:​kit:​housing:​housing_basket_food_liner.png?​direct&​256|}} | | |1| Basket Food Liner | {{:​kit:​housing:​housing_basket_food_liner.png?​direct&​256|}} | |
-|1| Rotor Pin Wrap | {{:​kit:​housing:​housing_rotor_pin_wrap.png?​direct&​256|}} | |+|1| Rotor Pin Wrap | {{:​kit:​housing:​housing_rotor_pin_wrap.png?​direct&​256|}} | This part is no longer used but still appears\\ on the sheet of styrene parts |
  
  
Line 103: Line 103:
 |2| Micro limit switch w/roller | {{:​kit:​bom:​bom_micro_limit_sw_256.jpg?​nolink|}} | \\ Be sure to buy the black-and-white switch pictured here. \\ \\ **Online shopping search term:** ultra mini micro limit switch roller ​ | |2| Micro limit switch w/roller | {{:​kit:​bom:​bom_micro_limit_sw_256.jpg?​nolink|}} | \\ Be sure to buy the black-and-white switch pictured here. \\ \\ **Online shopping search term:** ultra mini micro limit switch roller ​ |
 |1| PCB mount pushbutton | {{:​kit:​bom:​bom_pcb_button_256.jpg?​nolink|}} | \\ 6x6mm size recommended \\ \\ **Online shopping search term:** pcb mount dip tactile switch 6mm | |1| PCB mount pushbutton | {{:​kit:​bom:​bom_pcb_button_256.jpg?​nolink|}} | \\ 6x6mm size recommended \\ \\ **Online shopping search term:** pcb mount dip tactile switch 6mm |
-|1| MG995 Servo | {{:​kit:​bom:​bom_mg995_servo_256.jpg?​nolink|}} | \\ **Online shopping search term:** MG995 servo |+|1| MG995 Servo | {{:​kit:​bom:​bom_mg995_servo_256.jpg?​nolink|}} | **NOTE:** These servos are manufactured by several different companies and are sometimes sold with different assortments of accessories. Ensure that the servo you buy comes with a **six star horn** accessory, shown here: {{ :​kit:​bom:​bom_six_star_horn_256.jpg?​nolink&​200 |}} \\ **Online shopping search term:** MG995 servo |
 |asstd| Dupont jumper wires | {{:​kit:​bom:​bom_dupont_ribbon_gen_256.jpg?​nolink|}} | Select 10cm length, one set of male-to-male and one set of male-to-female. \\ \\ **Online shopping search term:** 10cm dupont m-m f-m | |asstd| Dupont jumper wires | {{:​kit:​bom:​bom_dupont_ribbon_gen_256.jpg?​nolink|}} | Select 10cm length, one set of male-to-male and one set of male-to-female. \\ \\ **Online shopping search term:** 10cm dupont m-m f-m |
 +|1 set| Dupont male with alligator clip | {{ :​kit:​bom:​bom_dupont_gators.jpg?​nolink |}} | Dupont male on one end, alligator clip on the other. \\ \\ **NOTE:** only two alligator clip wires are required. You can make your own by soldering alligator clips to ordinary dupont wires, if you already have the gator clips.\\ \\ **Online shopping search term:** dupont alligator clip |
 |1| 5mm terminal block | {{:​kit:​bom:​bom_5mm_terminal.jpg?​nolink|}} | \\ Color may be green or blue- it does not matter which you buy, just be sure to get 5mm pitch. \\ \\ **Online shopping search term:** 5mm terminal block 2p | |1| 5mm terminal block | {{:​kit:​bom:​bom_5mm_terminal.jpg?​nolink|}} | \\ Color may be green or blue- it does not matter which you buy, just be sure to get 5mm pitch. \\ \\ **Online shopping search term:** 5mm terminal block 2p |
 |asstd.| 3mm standoffs | {{ :​kit:​bom:​bom_3mm_standoffs.jpg?​nolink |}} | Nylon is recommended but brass is fine. Only three standoffs are required, recommended height is 8mm. \\ \\ **NOTE:** It's possible to cobble together standoffs using M3 screws and multiple nuts. \\ \\ **Online shopping search term:** 3mm standoff kit | |asstd.| 3mm standoffs | {{ :​kit:​bom:​bom_3mm_standoffs.jpg?​nolink |}} | Nylon is recommended but brass is fine. Only three standoffs are required, recommended height is 8mm. \\ \\ **NOTE:** It's possible to cobble together standoffs using M3 screws and multiple nuts. \\ \\ **Online shopping search term:** 3mm standoff kit |
kit/crowbox2_v20_bom.1536708164.txt.gz ยท Last modified: 2018/09/11 16:22 by steve