kit:housing_assembly
no way to compare when less than two revisions
Differences
This shows you the differences between two versions of the page.
Previous revision | |||
— | kit:housing_assembly [2018/08/01 13:37] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ====== Required Tools ====== | ||
+ | * Aspergillum (this is a joke) | ||
+ | |||
+ | ====== Required Supplies ====== | ||
+ | * Wood glue | ||
+ | |||
+ | ====== Assembly ====== | ||
+ | -Laminate the two BASE PLATE pieces together to make one thick plate (burned faces inward) | ||
+ | -Laminate the three PERCH ARM pieces together | ||
+ | -Assemble and use the PERCH ALIGNMENT TOOL for this. | ||
+ | -Clamp, press, etc. to ensure the PERCH ARM cures straight | ||
+ | -Attach 7RPM COIN MOTOR (and GASKET) to the COIN MOTOR SUPPORT | ||
+ | -Bolt heads must be on the inside (nuts on the motor side) | ||
+ | -M3x8mm machine screw x2 | ||
+ | -Black hex nut x2 | ||
+ | -Apply traction material (hot glue) to COIN DISPENSE CAM | ||
+ | -Stack these items onto the COIN MOTOR shaft: | ||
+ | -COIN CAM SPACER | ||
+ | -COIN CAM | ||
+ | -COIN CAM SPACER | ||
+ | -Bolt both COIN MOTOR MOUNT pieces to BACK PANEL | ||
+ | -M3x8mm machine screw x2 | ||
+ | -Black hex nut x2 | ||
+ | -Bolt COIN TUBE PLATFORM to BACK PANEL | ||
+ | -M3x8mm machine screw x1 | ||
+ | -Black hex nut x1 | ||
+ | -Bolt 2RPM REWARD MOTOR to MACHINE DECK | ||
+ | -Use Gasket! | ||
+ | -Bolt heads must be on top of the deck - nuts on the motor side | ||
+ | -M3x8mm machine screw x2 | ||
+ | -Black hex nut x2 | ||
+ | -Install reward wheel glide bolts | ||
+ | -Observe ‘triangle’ layout | ||
+ | -M3x8mm machine screw x3 | ||
+ | -Black hex nut x3 | ||
+ | -Bolt REAR PANEL to BASEPLATE with REAR BUTTRESS, using washers | ||
+ | -M3x12mm machine screw x2 | ||
+ | -Black washer x2 | ||
+ | -Black hex nut x2 | ||
+ | -Sandwich INNER DEPOSIT RAMP between PERCH PIVOT PANELS | ||
+ | -Press-fit, careful with force | ||
+ | -This part is now the PERCH PIVOT | ||
+ | -Bolt PERCH PIVOT assembly to BASEPLATE, using washers | ||
+ | -M3x12mm x4 | ||
+ | -Black washer x4 | ||
+ | -Black hex nut x4 | ||
+ | -Press together LOWER DEPOSIT RAMP assembly | ||
+ | -Bolt LOWER DEPOSIT RAMP to FRONT PANEL | ||
+ | -M3x12mm x2 | ||
+ | -Black hex nut x2 | ||
+ | -Press together RAMP AND CHUTE assembly | ||
+ | -Bolt RAMP and CHUTE assembly to FRONT PANEL | ||
+ | -Bolt TOP first, and use a washer | ||
+ | -Align and press RAMP into guides on COIN MOTOR MOUNT | ||
+ | -Bolt bottom pair, without washers | ||
+ | -Slot MACHINE DECK | ||
+ | -Bolt MACHINE DECK | ||
+ | -M3x12mm x3 | ||
+ | -Black washer x3 | ||
+ | -Black hex bolt x3 | ||
kit/housing_assembly.txt · Last modified: 2018/08/01 13:37 by 127.0.0.1