kit:parts_list_v007
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
kit:parts_list_v007 [2016/12/26 13:40] steve [Arduino Core] |
kit:parts_list_v007 [2018/08/01 13:37] (current) |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | Items marked with " | + | **NOTE: |
| + | |||
| + | **NOTE:** Shipping costs not included! This could be a silent killer. Some items assume Amazon Prime membership | ||
| Line 10: | Line 12: | ||
| *SD Card shield Cost: $2.00 | *SD Card shield Cost: $2.00 | ||
| - | Current total price: $28.00 | + | Current total cost: $28.00 |
| ==== Raspberry Pi Core ==== | ==== Raspberry Pi Core ==== | ||
| - | * Raspberry Pi Zero with camera | + | * Raspberry Pi Zero with camera bundle. Current best price: $40 (Adafruit) |
| * Raspberry Pi servo hat. Current best price: $18 (Adafruit) | * Raspberry Pi servo hat. Current best price: $18 (Adafruit) | ||
| + | * Edimax USB wifi dongle. Current best price: $8 (Amazon) | ||
| + | Current total cost: $66.00 | ||
| + | |||
| + | ===== Components ===== | ||
| + | * Hookup wire: 22AWG stranded. 25 feet RED, 25 feet BLACK. Cost: $6.00 for both spools | ||
| + | * Dupont jumpers: GET COUNT. GET LENGTH. DETERMINE ENDS. FIND SOURCE. | ||
| + | * 1x Half-size breadboard. Cost: $5.00 | ||
| + | * 3x Two-position screw terminals for breadboard. Cost $Repackaged from bulk | ||
| + | * 3x Mini limit switches for lid. Cost: $2.00 for three | ||
| + | * 4 pairs 22AWG m/f bullet terminals (8 pieces total) Cost: $Repackaged from bulk | ||
| + | * 8ft 24 AWG bare copper wire. Cost: 25 cents per CrowBox if bought in bulk & portioned | ||
| + | * Otherwise, cost for entire roll | ||
| + | |||
| + | Current total cost: $13.25 presently, but not all items accounted for yet. | ||
| + | |||
| + | ===== Voltage Regulator Components ===== | ||
| + | * The actual regulator chip | ||
| + | * LM7806CZ DC 1.5A Positive Voltage Regulator, 6V | ||
| + | * Capacitor #1 | ||
| + | * Capacitor #2 | ||
| + | * Diode | ||
| ===== Motor ===== | ===== Motor ===== | ||
| MG995 Metal gear servo. Current best price: $6.00 per servo | MG995 Metal gear servo. Current best price: $6.00 per servo | ||
| + | |||
| + | Current total cost: $6.00 | ||
| ====== Structural ====== | ====== Structural ====== | ||
| - | 1/4 inch acrylic rod (for push rod) | + | All information in this category currently assumes fabrication at PONOKO.COM |
| + | |||
| + | *1/4 inch acrylic rod (for push rod) | ||
| + | *790x384x3mm acrylic sheet (solid color) - Cost: $25.23 fabricated | ||
| + | *181x181x3mm acrylic sheet (translucent) - Cost: $4.50 fabricated | ||
| + | *384x384x3mm acrylic sheet (transparent) - Cost: $9.13 fabricated | ||
| + | *384x384x.5mm styrene sheet (white) - Cost: $2.50 fabricated | ||
| + | |||
| + | Current Cost: $41.36 plus shipping | ||
| + | |||
| ====== Fasteners ====== | ====== Fasteners ====== | ||
| - | M3 bolts (get specific on length, cap style, etc) | + | *M3 bolts (get specific on length, cap style, etc) |
| + | *M3 nuts | ||
| + | *Silicone rubber band for lid, two inch (include extras). Current best price: 25 cents per band | ||
| + | |||
| + | Current Cost: [Not done building the list of required fasteners] | ||
| + | |||
| + | ====== Grand Total ====== | ||
| + | **NOTE:** - This information is just the sum of the categories above. It WILL change before shipping. Some parts are not yet sourced, priced, or best-priced, | ||
| - | M3 nuts | + | ===== Arduino Core ===== |
| + | $88.61 | ||
| - | Silicone rubber band for lid, two inch (include extras). Current best price: 25 cents per band | + | ===== Raspberry Pi Core ===== |
| + | $126.61 | ||
kit/parts_list_v007.1482788410.txt.gz · Last modified: 2016/12/26 13:40 by steve
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
